Recent content by StupidFlanders

I have found the actuator is weak. I gave it three turns more preload and now my N75 duty is no more than 87% .

Just for anyone interested , my actuator is weak casing some of the issues above . You can buy replacement ones from turbo dynamics for the KO3 turbo 5825-110-4071R Remanufactured Actuator - VAG 5825-110-4071 Remanufactured Actuator - VAG [5825-110-4071R] - £12.00 : Turbo Dynamics...

sound like the thermotstat . Mine did the something similar , as the temp gauge is not that acurate . after changeing thermostat My vag com says temp is 97 but gauge is bang on 90 . Before gauge read 80 but temp was 61 on vag com. What engine code do you have ? as my temp on agu is block 3 or 4 .

TIME Spec Corrected Actual Duty RPM STAMP Load Load Load Cycle N75 ms ms ms % 215.79 5.7 5.6 4.25 99.6 1360 216.29 6 5.8 4.65 99.6 1440 216.79 6.85 6.3 5.05 99.6 1560 217.3 7.55 7.1 5.45 99.6 1680 217.79 7.6 7.45 5.85 99.6 1800 218.29 7.75 7.6 6.35 99.6 1920 218.79...

Time Specified Load Actual Duty Stamp Load Correction Load Cycle N75 RPM ms ms ms ms 424.66 7.7 6.65 4.65 99.6 2000 425.16 7.95 7.65 5.65 99.6 2160 425.66 8.3 8.1 7.15 92.6 2320 426.16 8.8 8.5 8.35 75.4 2560 426.66 9.25 9 8.7 73 2760 427.16 9.75 9.5 8.9 76.6 3000...

Nope standard cooler but its cold up north ! The highest temps i have seen are 39 . I do have an 80mm cold air intake to the airbox and always run on v power

Thanks , i started by making small adjustments until i reached a point where requested load met actual load all through the rev range with the n75 highest duty being 95% . When i thought about it being rich , and the n75 being at max it was not flowing enough air . I will post up the log on...

Done some testing today. Took plugs out and they are black showing rich mixture. Lambda is new and i have no leaks(all smoke tested). I then adjusted my actuator two turns more preload. Now my load values match , peak boost is 18 psi and the N75 is now showing a max of 95% which i think is what...

Thanks for the reply . I will post up a section of my log. I would just like to know if the agu stage 1 always asks for more than the little ko3 can provide.

Hi does anyone have some vag com or vcds logs of block 25 on an AGU revo remap ? Im looking to compare with mine as after having all vac piipes and boost pips replaced (also PCV ) my requested load never matches actual load and the N75 duty is pegged at 99.6% . Boost gauge reads peak of...

Hi does anyone have some vag com or vcds logs of block 25 on a stage 1 AGU revo remap ? Im looking to compare with mine as after having all vac piipes and boost pips replaced (also PCV ) my requested load never matches actual load and the N75 duty is pegged at 99.6% . Boost gauge reads peak of...

Hi , my AGU feels a bit down on torque from when i first got it mapped. I run it on V power , timing pull is no more than 2.2 . Here is a sampl of my log . My max MAF as below. Does this seem a little low or do AGU read lower the DBW cars . 5520 8 16.32 140.62 5640 7.9 16.32...

Hi , my AGU feels a bit down on torque from when i first got it mapped. I run it on V power , timing pull is no more than 2.2 . Here is a sampl of my log . My max MAF as below. Does this seem a little low or do AGU read lower the DBW cars . 5520 8 16.32 140.62 5640...

Just a quick hi , have a 1998 A3 AGU with stage one REVO . This is my first audi , i use it as a daily driver to work . Might need some help with VCDS logs .