Hi All,
I'm looking to spray / refurb my leather seats. Does anyone know the paint code for the red for the red/black leather seats - these are electric/heated if that helps.
Thanks in advance.
Hi All,
So, I've managed to fit the electric / heated seats. The issue I am having is on the passenger side, when I slide the seat to either end the 10A fuse blows, the same happens on the drivers side where I raise or lower the seat and the fuse blows. What I noticed is, if I use a 15A fuse...
Hi All,
As the title suggests, the passenger side is reaching 29 degrees and then stops, the seat is warm, from VCDS the 'Temp. (Spec) is 39 degrees. The interesting thing is, if I switch off (position '0') VCDS continues displaying 29 degrees.
The driver side reading 'Temp (Act)', with the...
Hi All,
I'm currently fitting some electric seats using the Kufatec loom. There are two cables for the fuse box, I presume one is for the driver and the other passenger? However, the fuse box table only has one position for the Driver side and passenger side:
Hi All,
I'm looking to run in another live wire attached to the bar behind the fusebox. Apologies, unsure of the correct terms here. Where can I purchase this? Pic attached
Hi All,
I've just finished swapping over the panels on my A3 which is now a nice misano red. However, the car needs a little TLC and colour matching. I need a few scuffs removed + colour matching. I'm based near St. Albans, but happy to travel round the south for the right body shop
So...
Hi All,
I hope you're well. Just trying to figure out where the headlight range module is installed. I believe its underneath the drivers side, but cannot locate the position. I've attached a pic of underneath the dash for reference.
Hi All,
I've retro fit the headlight washer system, I've attempted to run it with engine on + lights on but nothing. I've put on VCDS and get the following:
00924 - Relay for Headlamp Cleaning System (J39)
009 - Open or Short to Ground - Intermittent
To check, the fuse I'm using...
Hi All,
I'm trying to workout if its the bumper or the bonnet causing the gap. Also, depending upon which it is how do I then adjust either side to get rid of the gap?
Hi All,
I'm looking for the repair wire part number for the wire that runs to the auto-levelling sensor located at the rear of the vehicle. Probably going to need a 3 metres worth.
Hi All,
I'm attempting to code the rear parking sensors on my A3 8P. The module I installed is: 8P0 919 475 G and coding is default to 00003. I've logged in with the security code and setup the User Interface and Identification with values other than 0. However, I'm getting the message Error...
Hi All,
I'm looking for the location for the front levelling sensor. I've looked at a few pics online but cannot find it on mine. KUFATEC have also said not all 2010 models have the front sensor, unsure if thats true. Can someone help?
Hi All,
I recently picked up some 5 door red and black 8P seats. They are electric but unsure if they're heated. Reading around it seems as if the heats are electric then they are also heated? Do I need to hunt for the part number to be sure?
TIA
Hi All,
Busy weekend, almost done. Last pin for the auto levelling and cornering wiring loom. The Kufatec describe this pin as 'light on' and the instructions say the pin goes T52a /11 on my 2010 model. However, according to the wiring diagram T52a /11 = J343 (Left HID headlamp control...
Hi All,
I've got the CAN Bus gateway connector unplugged. But I cannot for the life of me work out how to remove it from the housing. Trying to locate pin 6, I would use the colouring system but theres a few other cables which are orange/brown.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.