Hello, ive jumped over here from the B7 section as i need to know which muffler deletes (K03/K04) fit the turbo mentioned as per title as im fitting one of these turbo’s to my B7 DTM.
Any help appreciated
DRL as CHL Function
You need to have DRL’s (OEM Xenon lights) and rain/light sensor fitted (auto lights) and have BCM control module with the part number 8E0 907 279 (N or L)
Fit the Switch for DRL/CHL - 8E2 919 094 D
Code address 09 with VCDS or similar according to cars spec then do the...
Ok so i have coded my car to have CHL and nothing happens lol i have then seen that you need the correct switch next to the light switch so as mine just has a DRL one fitted i have ordered one with CHL/DRL knobs.
Is anything else needed to have this function?
i unplugged the light switch and...
Can anyone confirm that if i fitted the ‘Maxi’ front door motor/modules 8e2959802e and 8e2959801e from a circa 2010 seat exeo to my 2006 DTM that i would then have folding mirrors on locking/unlocking without any other modifications needed for this to work as i have read this can be done as...
As per title looking to purchase some control arms for the front on my DTM im leaning towards meyle hd kit from ebay at £390 (part number :- 116 050 0085/HD)
Anyone know anywhere cheaper or any alternative kits that are about the same quality as meyle or lemforder.
Thanks in advance
Thought id start a progress thread for my DTM as my cars never seem to stay standard for long have a look at my B5 thread if you fancy a read sadly its been scrapped had big plans for it but it never panned out the way i was hoping loved that car hopefully this DTM will fill its shoes for some...
had a look into this and believe its the balance shaft unit seen kits on ebay for £450 to use the 1.8T pump set up can i just source the parts individually or do i need that kit to recoil the mounting bolts or can i just use the part numbers listed below to do a DIY delete ?? Any help...
im after the part numbers for the LCR top mounts and bearings etc
And also the front wheel bearing either genuine, skf or fag ? I found too skf on ebay listed for my car one being vkba 3455 which i think is correct but also vkba 3607
TIA
Was looking for subframe bushes for my TQS, i was tempted to go the 034 billet route but read up they can creak and i came across some ak motorsport polyurethane bushes and im more tempted to go this route anyone had any first hand experience with either bushes ?
When i got the car it was apparent that the cylinder head coolant housing had been leaking at some point and had been replaced at a later date as i think someone had just kept adding water with no anti-freeze or had used a sealing addative like k-seal as the coolant tank was full of a rusty...
whats the part number for the bigger black washer cap.
As ive just recieved this of ebay and is way too small and doesn't fit.....
Is there one that fits the S3 8L ??
This was listed for a 1999-2014 audi TT
Best place to source control arms from as bushes are detaching and it appears my n/s arm is bent slightly possibly why the tracking needs attention.
Looking at allgermanparts meyle arms but may look at polybushing at some stage.
does anyone know part numbers for s3 bam timing belt/water pump kits ?
Gates or contitech ?
I was looking at ct909wp1 is this the correct kit ??
Also is there one that deletes the hydraulic tensioner for a manual one ??
TIA
Hi all im now the proud owner off a S3 8L not new to the forum at all been on here a few years. Mainly in the B5 section and recently the B6 section, My B5 is currently off the road as ive stripped it all to do BT/Stroker build and ended up with a 6N2 polo 1.4tdi as a stop gap for a daily when i...
Although i like the cab ive had the idea of selling up next year and i happened to come across a S3 8L 52 plate with 132k and i enquired about part exchanging mine for the S3 8L as a straight swap and they have said they will take it should i go ahead with it ?? Cabs a 55 plate 1.8T sport with...
ive been thinking about this recently could you fit the turbo and cat from a A4 B7 2.0TFSI with a 1.8T adapter plate like beachbuggys to the 1.8T BFB with some custom intake pipe work.
gone to put some led's in today and one side is completely siezed on at the grub screw. Also noticed my lock barrel wont turn left or right suspect this is another common issue with the plinth corroding due to being aluminium ?
Anyone know the cost from TPS for one ??
my B6 A4 cabs o/s/r window works fine until it wants to go fully down its leaving about 3-4inch off the window showing, is this common or do i need to see if my youngest has shoved something down the window as thats the side he sits on lol
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.