Search results for query: *

Hi, I hope someone out there can help me please. I have a manual transmission Audi Q3 2016 (MY) - S-line plus and I would like to change the pedals to the RS Alloy / Rubber type pedals. (As found in black editions). Previously on my A3, I swapped the pedals to this type of pedal, but I...

Thank you for replying. I will just be using the standard length lead supplied with the kit, so hopefully that will be fine. Cheers.

Hi Folks, I'm just after some advice really. I've just acquired a Pure Highway DAB unit and I'm toying with the idea of installing the aerial on the rear drivers side quarter light window and running the cable under the carpets & along the inner sill. Instead of the suggested upper corner on...

Yes, that's exactly why I swapped out the amps to get rid of the error message and to have a clean VCDS scan etc. But it's good to know that your Autodab unit worked on that configuration, so thank you. No, I can't access any of the radio channels now they are all greyed out, since I got the...

Send me a personal message is the best way.

Hi, Please see up loaded PDF file. If you can print it on to A4 paper and just double check the sizes. (I've just tried it on my printer again and it comes out spot on to actual scale.) But please do you own checks first to ensure. I also have the instructions, but they exceed the permitted...

Hi, You can download the template to lay over the centre console to make sure you cut the hole in the right place. I may still have the PDF file somewhere, which I will try and upload, if you need it. Its fairly easy to do, its just a leap of faith cutting in to the plastic as its a point of no...

Hi, Thank you for all the replies and for the offers of Autodab units, very generous. However, the support team at Connects2 got back to me yesterday and suggested that I check the Fakra connections as the most likely cause of the issue. Upon checking, one of the individual leaf contacts in the...

Thank you for your reply. Yes, my rnse is running the latest firmware version. However, when I mentioned the version of the firmware in my post, I was referring to the Autodab units firmware, sorry if I didn’t make the clear. Thanks again.

Thank you Matt268uk for taking the time to respond. The top of the aerial strip is fitted at least 15cm below the top of the wind screen, so its more towards the middle of the screen by the time you get to the amplifier box. I've been on a 120 mile round trip today into a city centre and still...

Hi Folks, I recently purchased a 'pre-owned' Autodab unit for my A3 (which has the RNSE head unit installed) and connected it up over the weekend. The Autodab unit appears to be working, as it responds to the MFSW buttons and I can listen to numerous radio channels........All good! However...

Hi, No problem mate. Before you buy a new sensor, I would just open the drivers door, pull back the rubber boot and inspect the wires in the door loom. I expect you will find a broke wire (the two wires running to the door sensors are brown & yellow which are both really thin in gauge - in my...

Hi John, Thank you for getting back to me. Since re-clearing the errors, so far they have not returned....... Thinking back, maybe I disconnected one of the amp connections after the initial install, test & VCDS run (which was clear.) Which subsequently then tripped the new error code...

Hi, Final update from me on this one......As my previous post above didn't actually fix the problem in the end. As the air bag warning light came back on again a couple of day's later. This time I read the error message properly and although it is exactly the same as the one at the beginning...

Thank you for taking the time to reply, that is what I had done. As stated in my post I only have the one existing / original wire running to the amp not two, as mine is a revised spec from the factory being a later model...so I was jut checking that it should to the yellow connection on the...

Hi Guys, I'm hoping someone can help me out please. I've just completed this amp swap out conversion and everything seems to work OK on the surface. However, when I scan the car now I get the following error codes: Address 37: Navigation Labels: 8E0-035-192-RNSE.lbl Part No SW: 8P0...

Hi Folks, Just a quick update, I’ve now finally managed to clear my air bag warning light issue (as stated above). Ultimately, I think it was just a connection issue, but I couldn’t see anything obvious…..And after trying the sensor swap over as previously described in this post, I still...

WANTED : AUTODAB FOR AUDI A3 - CTDAB-AU1 - MUST BE QUADLOCK VERSION. NEW preferred , but will consider used as long as its in full working order. Thank you.

No, I left the battery connected. Typical, that's just my luck about it not being an easy fix, but I'll get a second opinion on the problem. I'll post the outcome here when I know what is along with the fix.....and probably a few tears as well. Cheers,

No worries Buddy. I decided to grasp the nettle and just did it. Unfortunately for me, the problem seems to be the wiring loom as when I swapped the sensors over, cleared the existing error code down & re-scanned, I still had the same error being returned. Checked the wiring that is visible...