ive fitted footwell lighting all 4 .........and heater vent dial lighting.......oh and here.........Enable Hidden menu in MMI
Audi A4/S4/A5/S5 B8
VCDS (VAG-COM) codes
Enable Hidden menu in MMI 3G
[5F - Information Electr.]
[Adaptation - 10] -> Channel 6
change 0 to 1
To access the hidden menu, hold down car and setup together for 5 seconds
Use this hidden menu at your own risk.
Enable Hidden menu in MMI 2G
[07 - Control Head]
[Adaptation - 10] -> Channel 8 -> Change 0 to 1
To access the hidden menu, hold down car and setup together for 5 seconds
Use this hidden menu at your own risk. Caution: Keep away from the "Bootloader"
________________________________________
Adjust bluetooth microphone sensitivity
Hidden menu
Diagnose
Settings
Mic sensiblity - choose -6db/0db/+6db
________________________________________
Change MMI 3G splashscreen...
Enable through the "hidden menu":
- navigate to 'car/carcodingvehicle'
- choose the model of choice in 'configuration line'
- select 'Update Splashscreen'
- restart MMI
________________________________________
Disable After-wipe of windscreen wipers
[09 â Cent. Elect.] [Coding - 07] -> [Dropdown] -> "x ** 8K1 955 119 ** WWS xxxx" -> Long Coding Helper -> Byte 1
Bit 3 - Remove check mark (1 = active)
________________________________________
Disable amber corner lights
[09 â Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 10
Submodule 0
Bit 3 - Set to 0 to disable amber side markers (U.S. vehicles)
________________________________________
Disable Key warning (keyless models)
[46 â Central Conv.] [Coding - 07] -> Long Coding Helper -> Byte 9
Bit 7 set to 0 (Uncheck)
________________________________________
Disable LED 'wink' on turn signal - pre facelift
[09 â Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 3
Bit 2 - LEDs remain at full brightness with parking lights (1 = active)
Bit 7 - Turn off LED-strip DRLs with indicators (1 = active)
________________________________________
Disable LED 'wink' on turn signal - facelift
09 â Cent. Elect.] [Security Access - 16] (enter security code. One of the default codes is- 20113)
[Adaptation - 10] -> Channel 3 (Heading Wink Brightness)
Default Value is 26, Setting value to 88 (Makes it identical to normal brightness)
________________________________________
Disable bulb error message with LED reverse lights installed
CREE LED reverse lights with RESISTOR and I STILL get a bulb out warning?
________________________________________
Disable "Lights are on" Warning
[09 â Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 5
Bit 3 - Set to 0 to disable "lights are on" warning when you open the door.
________________________________________
Disable NAV & Phone warning messages while entering data at speed
[5F - Information Electr.] -> Adaptation -> Set channel 2 & 3 to 250
________________________________________
Disable Seatbelt Chime
[17 - Instruments] [Coding - 07] -> Long Coding Helper -> Byte 0
Bit 2-4 â Seat Belt Warning inactive
________________________________________
To mute the Soundaktuator
A9 Structure Borne Sound
Adaptation 10
At Channel drop down choose "Volume of structure borne noise actuator" (only choice)
Enter a value in the proper box (0% = mute )
________________________________________
Enable Adaptive brake lights
[46 - Comfort System] [Coding - 07] -> Long Coding Helper -> Byte 8
Bit 0 â Emergency Brake Flashing via Turn Lights active (1 = active)
Bit 1 â Emergency Brake Flashing via Brake Lights active (1 = active)
________________________________________
Enable Optical rear parking for cars without front parking sensors
[10 - Park/Steer Assist] [16 - Security Access - 71679] do it [07 - Coding] Byte 0 - Bit 4 change 0 to 1
________________________________________
Enable Automatic Gear selection shown in DIS
[02 â Auto Trans] [Adaptation â 10]
Select âSingle Gear Displayâ from top channel drop down menu
Select âD on/S onâ from New value drop down menu
________________________________________
Enable Automatic Hill Hold Assist âliteâ*only works on certain abs modules - see below link*
[03 - ABS brakes][Security Access - 16] (Enter code presented by program)
[Coding â 07] -> Long Coding Helper -> Byte 1
Bit 6 set to 1 to enable hill hold assist.
AudiEnthusiasts TPMS
________________________________________
Enable Auxiliary ventilation
[5F - Information Electr.] [Coding - 07] -> Long Coding Helper -> Byte 6
Bit 1 â Set to 1
[Hidden menu] [car] [cardevicelist] [Auxiliary heating] Enable
[08 - Auto HVAC] [Coding - 07] -> Long Coding Helper -> Byte 1
Bit 3 â Set to 1
Bit 4 â Set to 1
________________________________________
Enable Battery meter *does not appear to work on facelift cars with MMI 3G+ HDD Navigation*
For MMI equipped cars
[Hidden menu] [car] [cardevextdevicelist] [Battery] Enable
[Hidden menu] [car] [carmenuoperation] [Battery] Set to 5
Reset MMI
or
[56 - Radio] -> Adaption -> Channel 39, add 16 to your value
For symphony, Chorus and Concert
Select module 56 - Radio
Select âAdaptation â 10
Select channel 39
Add 16 to the present value
"test"
"save"
âDone, Go Backâ and "Close Controller
________________________________________
Enable DIS with Efficiency Program for MY2010+ (Not a complete Program without the Start/Stop System)
[17 - Instruments] [Adaptation - 10] -> Channel 77
change 0 to 255
________________________________________
Enable Double Disarm Beep
[46 - Central Conv.] [Adaptation - 10] -> Channel 63
Add 4
ensure Module 46, Byte 1, Bit 2 is ticked. This activates the alarm audible notification option
________________________________________
Enable Drivers Memory Seat
36: Seat Mem - 07 Coding - Long Coding Helper - change Byte 2, bit 0, to 1
Seat memory will be there however greyed out in MMI
Press and hold down unlock button on key fob for 5 seconds for the windows to come down
Press and hold down lock button on key fob for 5 seconds for the windows to go back up
In MMI, Seat Adjustment you are now able to find Driver's seat, you can set Key memory on/off. Set it "on" for both keys separately.
________________________________________
Enable DRL Selectable via MMI
[09 â Cent. Elect.] -> [Coding â 07] -> Long Coding Helper -> Byte 3
Bit 5 set to 1
________________________________________
Enable DRL
[09 â Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 2
Bit 1 = DRL via Front Side markers
Bit 2 = DRL via High Beams
Bit 3 = DRL via Fogs
Bit 4 = DRL via LEDs
Bit 6 = DRL via Side markers
Bit 7 = DRL via Tail lights
________________________________________
Enable Audi Drive Select without the buttons
By far the best guide is here -
AudiEnthusiasts Vag Com
________________________________________
Enable Euro parking lights that turn on signal at night
[09 â Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 9
Bit 0 - Set to 1
________________________________________
Enable interior lighting option for pre-facelift
MMI Basic (Symphony/Concert radio) - (NON-MMI - 2G/3G):
Code:
[56 - Radio]
[Coding - 07] -> Long Coding Helper -> Byte 8 Bit 7 - Interior Light Settings active - (1 = active)
MMI high (2G):
Code: Enable the Interior lighting (extended) MMI item:
[07 - Control Head]
[Adaptation - 10] -> Channel 1 add 2 to the existing value
MMI high (2G hidden menu as alternative)
If you choose to use the 2G hidden menu you will find the setting using the following:
DIAG SETTINGS -> APK 0x01, 0x0B, 0x0C -> Interior lighting (extended)
MMI 3G
This can only be activated through hidden menu
Enter hidden menu - choose car - choose carmenuoperation - select interior light - set to 5 to allow adjustment whist moving - press return - select cardevicelist - choose interior light and press to fill box in - press return
Reset MMI (press setup, scroll wheel and top right button next to scroll wheel at the same time)
Option will show in MMI
Enable interior lighting for facelift cars
[09 â Cent. Elect.]
[Coding - 07] -> [Long Coding Helper] -> Byte 16
Bit 6 - Interior/Ambience Lighting Adaptation active
Hidden menu - [carbusassignment] - Interior Light to [CAN Komfort 1/9]"
________________________________________
Enable fog lamp to come on for the same side as that turn signal
[09 â Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 4
Bit 0 - Check the box or change :Bit 0 set to 1
________________________________________
Enable Front Turn Signals as Parking lights
[09 â Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 10
Bit 0- Check the box or change :Bit 0 to 1
Once the change has been made you can enable the front turn signals as DRL's by making the following change:
[09 â Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 2
Bit 6 - Check the box or change :Bit 0 set to 1
________________________________________
Enable Gauge Test/Needle Sweep
[17 - Instruments] [Coding - 07] -> Long Coding Helper -> Byte 1
Bit 0 - Check the box for "Gauge Test/Needle Sweep active"
________________________________________
Enable Headlights on all the time
[09 â Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 4
Bit 5 - Check the box or change (Bit 5 Set to 1)
________________________________________
Enable Import CDs to MMI's HD
[Hidden menu]
Main/Diagnose/Settings
Import Media
Set to 4 of 4 "Copy/Ripping"
________________________________________
Enable Independent Fogs control with high beams
[09 â Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 4
Bit 1 â (Front) Uncheck the box or change :Bit 1 to 0
Bit 2 â (Rear) Uncheck the box or change :Bit 2 to 0
________________________________________
Enable Lap Timer
[17 - Instruments] [Coding - 07] -> Long Coding Helper -> Byte 1
Bit 3 - Check the box for "Lap Timer active"
______________________________________
Enable Remote Operation Windows and Sunroof
[46 - Cent. Conv.] [Coding - 07] -> [Long Coding Helper] Byte 2
Bit 2 - Set to 1
______________________________________
Enable Rear Tail Lights on with DRLs
[09 â Cent. Elect.] [Coding - 07] -> Long Coding Helper -> Byte 2
Bit 7 - DRL's via Tail Lets Active (1 = Active)
________________________________________
Enable Release Parking Brake without putting foot on Brake
[53 - Parking Brake][Security Access - 16] (Enter code presented by program)
[Adaptation - 10] -> Channel 4 Set to 0
________________________________________
Enable Release Parking Brake without putting seatbelt
[53 - Parking Brake][Security Access - 16] (Enter code presented by program)
[Adaptation - 10] -> Channel 7 Set to 0
________________________________________
Enable Reverse mirror tilt
[52 Door Elect, Pass.] -> [Coding - 07] -> [Long Coding Helper] -> Byte 4
Bit 3 and Bit 2 set to 1
________________________________________
Enable Speed through MMI
[56 - Radio] [Adaptation - 10] -> Channel 02, Set to 1
Does not work if NAV equiped
________________________________________
Enable âTouristâ Mode â Headlight Convertor (MMI 2G)
[09-Central Elect]
[Coding â 07]
[Long Coding Helper] - Byte 4, Bit 6 = 1
Enables the 'connection' between Cent. Elect and the Headlight Convertor MMI menu item
[55-Xenon Range]
[Adaptation â 10]
[Channel 10] - 0 = Disable 1 = Enable
Press âTestâ and then âSaveâ
Enables the Headlight Convertor MMI item under the CAR button.
Restart MMI to see changes.
________________________________________
Enable TPMS
* only works with certain ABS modules - see below link *
AudiEnthusiasts TPMS
________________________________________
Enable Video in motion on MMI
[5F - Information Electr.] [Advanced ID - 1A] Note 1st Serial number
[Security Access] Enter Digits 6, 13, 10, 14, 11 of the 1st Serial number
[Adaptation - 10] -> Channel 48
Set to 255
Reset MMI
________________________________________
Set Audi parking system - Switch OFF Speed
[10 - Park/Steer Assist] [Adaptation - 10] -> Channel 23
Set to 20 (max value in km/h)
________________________________________
Set ADS to specific preset Comfort, Auto, Dynamic or Individual
[09 â Cent. Elect.][Security Access - 16]
[Adaptation - 10] -> Channel 63
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
[Adaptation - 10] -> Channel 64
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
[Adaptation - 10] -> Channel 65
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
[Adaptation - 10] -> Channel 66
Set to 01 - Comfort, 02 - Auto, 03 - Dynamic or 04 - Individual
*Note all four channels needs to be set to the same value.
________________________________________
Set Headlight washer - Duration
[09 â Cent. Elect.]
[Security Access - 16] [Adaptation - 10] -> Channel 6
change to e.g. 500
________________________________________
Set Headlight washer - Cycles
[09 â Cent. Elect.]
[Security Access - 16] [Adaptation - 10] -> Channel 26
change to e.g. 10
________________________________________
Adjust Consumption in DIS
[17 - Instruments]
[Adaptation - 10] -> Channel 3
change 100 to xxx (see samples below)
Sample 1 - Calculation based on volume per distance (e.g. l/100km):
DIS: 9,3 l/100 km.
Real: 9,8 l/100 km. (100 * 9,8 / 9,3 = 105,38)
Channel 3 will be changed from 100 to 105
Sample 2 - Calculation based on distance per volume (e.g. MPG):
DIS: 23 MPG.
Real: 24 MPG. (100 * 23 / 24 = 95,83)
Channel 3 will be changed from 100 to 96
________________________________________
Adjust LED brightness
[09 â Cent. Elect.] [Security Access - 16] (enter security code. One of the default codes is- 20113)
[Adaptation - 10] -> Channel 03
Set between 5 and 100 (5 being lowest and 100 brightest)
________________________________________
Select language in DIS:
17 - Instruments
Byte 8 -> Bit 0-4 - ->
Select the language.
________________________________________
Activate SDS for cabriolet:
5FâInformation Electr.
Change Byte 15 â Bit 0 to 1
Change Byte 16 â Bit 0 to 0
________________________________________
Change fuel-tank charisterics:
17 - Instruments
Adaption - change channels 30 and 33
________________________________________
To increase radio play time after car is turned off:
In the Hidden Menu:
MMI 2G:
"MMI->SETTINGS->Standby Timer" - will allow you to hear e.g. Radio or CD longer before MMI shutdown (if ignition is OFF) - default 10 min. and the max. is 60 min.
MMI 3G:
From the main screen select 'onofftimer', set 'Standby delay'. The maximum value is 30 minutes.
--------------------------------------------------------------------------------